Local de publicação venue para
- Bioinspired approaches for toughening of fibre reinforced polymer composites 2021
- 45S5 BAG-Ti6A14V structures: The influence of the design on some of the physical and chemical interactions that drive cellular response 2018
- Piezoresistive response of extruded polyaniline/(styrene-butadiene-styrene) polymer blends for force and deformation sensors 2018
- Superhard CrN/MoN coatings with multilayer architecture 2018
- Cyclic temperature dependence of electrical conductivity in polyanilines as a function of the dopant and synthesis method 2017
-
Effect of sintering pressure on microstructure and mechanical properties of hot-pressed Ti6Al4V-ZrO
2 materials 2017 - A green solvent strategy for the development of piezoelectric poly(vinylidene fluoride-trifluoroethylene) films for sensors and actuators applications 2016
- Characterization of Metglas/poly(vinylidene fluoride)/Metglas magnetoelectric laminates for AC/DC magnetic sensor applications 2016
- Strategies for the development of three dimensional scaffolds from piezoelectric poly(vinylidene fluoride) 2016
- Study on the impact behaviour of a new safety toe cap model made of ultra-high-strength steels 2016
- Development of novel auxetic textile structures using high performance fibres 2016
- Low pressure sand casting of ultrasonically degassed Al7SiMg alloy: Modelling and experimental validation of mould filling 2016
- Multi-level characterization of steel reinforced mortars for strengthening of masonry structures 2016
- Nonsolvent induced phase separation preparation of poly(vinylidene fluoride-co-chlorotrifluoroethylene) membranes with tailored morphology, piezoelectric phase content and mechanical properties 2015
- Cork-polymer biocomposites: Mechanical, structural and thermal properties 2015
- Fused deposition modeling with polypropylene 2015
- Influence of design parameters on the mechanical behavior and porosity of braided fibrous stents 2015
- Development of novel auxetic structures based on braided composites 2014
- Dry sliding and tribocorrosion behaviour of hot pressed CoCrMo biomedical alloy as compared with the cast CoCrMo and Ti6Al4V alloys 2013
- Integrating environmental and economic life cycle analysis in product development: A material selection case study 2013
- The quest for a sustainable product: An environmental study of tyre recyclates 2013
- Modelling the environmental performance of composite products : benchmark with traditional materials 2012
- The effect of Sc additions on the microstructure and age hardening behaviour of as cast Al-Sc alloys 2012
- Challenges in the harmonisation and digitalisation of Environmental Product Declarations for construction products in the European context. 29. 2024
- Unravelling the physics and mechanisms behind slips and falls on icy surfaces: A comprehensive review and nature-inspired solutions. 234:112335. 2023
- Bioinspired Approaches for Toughening of Fibre Reinforced Polymer Composites. 199. 2021
- A review on intrinsic self-sensing cementitious composites and prospects for application in transport infrastructures 2021
- Computational and experimental characterization of 3D-printed PCL structures toward the design of soft biological tissue scaffolds. 188:108488-108488. 2020
- Corrigendum to “Development of a method to produce FGMs by controlling the reinforcement distribution” [Materials and Design 92 (2016) 233–239]. (Materials and Design (2016) 92 (233–239), (S0264127515308911), (10.1016/j.matdes.2015.12.032)). 195. 2020
- Life cycle assessment of retaining wall backfilled with shredded tires 2019
- Time-effective synthesis of rhombohedral CuAlO2 from mesoporous alumina substrate. 147:48-55. 2018
- TEMPO-oxidized cellulose nanofibers as interfacial strengthener in continuous-fiber reinforced polymer composites. 133:340-348. 2017
- Effect of sintering pressure on microstructure and mechanical properties of hot-pressed Ti6Al4V-ZrO2 materials 2017
- Design of Ti6Al4V-HA composites produced by hot pressing for biomedical applications. 108:488-493. 2016
- Development of a method to produce FGMs by controlling the reinforcement distribution. 92:233-239. 2016
-
Optimization of the MgOSiO
2 binding system for fiber-cement production with cellulosic reinforcing elements. 105:251-261. 2016 - The effect of SiC p size on high temperature damping capacity and dynamic Young's modulus of hot-pressed AlSi–SiC p MMCs. 93:409-417. 2016
- Optimization of AlSi-CNTs functionally graded material composites for engine piston rings. 80:163-173. 2015
- Mechanical properties of hot pressed CoCrMo alloy compacts for biomedical applications. 83:829-834. 2015
- Effect of friction stir welding parameters on morphology and strength of acrylonitrile butadiene styrene plate welds. 58:457-464. 2014
- Influence of the plastic anisotropy modelling in the reverse deep drawing process simulation. 60:368-379. 2014
- Morphology and strength of acrylonitrile butadiene styrene welds performed by robotic friction stir welding. 64:81-90. 2014
- Blast response of cracked steel box structures repaired with carbon fibre-reinforced polymer composite patch. 32:3092-3098. 2011
- Sensitivity of different Al-Si alloys to centrifugal casting effect. 31:2867-2877. 2010
- Influence of vibration on the solidification behaviour and tensile properties of an Al-18 wt%Si alloy. 30:1575-1580. 2009
- Sensitivity study on some parameters in blank design. 30:1223-1230. 2009
- Advantages of the centrifugal casting technique for the production of structural components with Al-Si alloys. 29:20-27. 2008
- Rapid prototyping with high power fiber lasers 2008